Tilt-Lock offers several models of Tip Lifts. Tip Lifts are furnished with either electric or pneumatic power. All units feature ergonomically designed handle mounted controls for combined control of the hoist and the Tip Lift. The controls are designed for ease of operation and operator control and safety.
The spring loaded Tip Lift probe is easily inserted into the core of material. Four gravity activated teeth on the end of the probe grip the core firmly.
This patented probe design assures that the load cannot be disengaged from the probe while the load is suspended in the air. With the probe inserted into the roll, it may be rotated 90 degrees and moved to the required location. When the roll has been placed on a stationary support, the teeth of the probe may be retracted using either a manual release handle or by
activating the pneumatic release feature.
The Tilt Lock Model LD1 Tip Lift is designed to handle light rolls of paper up to 340 pounds. The lightweight model utilizes ergonomically designed handles and controls featuring interlocking Safety Switches. The LD1 is equipped with a short probe and manual tooth release. This unit is perfect for handling small rolls in areas with low headroom. The Model LD1 weighs
67 pounds., with fused power and control circuits. Tilt-lock recommends using electric chain hoists with 115-1-60 power supply and a lifting speed of 16 fpm.
The Tilt Lock Model LS1 Tip Lift is designed to handle rolls of paper up to 830 pounds. The LS1 model utilizes handle mounted controls combining hoist and tip lift functions at the operators finger tips. The controls also integrate an interlock feature that requires the operator to have both hands in the correct position on the controls preventin 1050 g accidental
hand placement. This unit is perfect for handling rolls in areas with low headroom. The Model LS1 weighs 110 pounds. Electric actuator not to exceed 35 cycles per hour under full load. Actuator motor is thermally protected against excessive heat build up during operation. After cooling down actuator will resume normal operation. Tip Lift power requirement is 115-1-60
and 7.5 amps. Minimum 3" wide roll is required for probes to work properly. Tip Lift is supplied with a quick release pin for interchanging probes to accommodate 3" to 12" diameter cores. Tilt-lock recommends using electric chain hoists with 115-1-60 power supply and a lifting speed of 16 fpm.
The Tilt Lock Model L1 Tip Lift is designed to handle rolls of paper up to 930 pounds. The L1 model utilizes handle mounted controls combining hoist and tip lift functions at the operators finger tips. The controls also integrate an interlock feature that requires the operator to have both hands in the correct position on the controls preventing accidental hand placement.
The Model L1 weighs 115 pounds. Electric actuator not to exceed 35 cycles per hour under full load. Actuator motor is thermally protected against excessive heat build up during operation. After cooling down actuator will resume normal operation. Tip Lift power requirement is 115-1-60 and 7.5 amps. Minimum 3" wide roll is required for probes to work properly. Tip Lift
is supplied with a quick release pin for interchanging probes to accommodate 3" to 12" diameter cores. Tilt-lock recommends using electric chain hoists with 115-1-60 power supply and a lifting speed of 16 fpm.
The Tilt Lock Model L2 Tip Lift is designed to handle rolls of paper up to 2,000 pounds. The L2 model utilizes handle mounted controls combining hoist and tip lift functions at the operators finger tips. The controls also integrate an interlock feature that requires the operator to have both hands in the correct position on the controls preventing accidental hand
placement. The Model L2 weighs 145 pounds. Electric actuator not to exceed 10 cycles per hour under full load. Actuator motor is thermally protected against excessive heat build up during operation. After cooling down actuator will resume normal operation. Tip Lift power requirement is 115-1-60 and 7.5 amps. Minimum 3" wide roll is required for probes to work properly.
Tip Lift is supplied with a quick release pin for interchanging probes to accommodate 3" to 12" diameter cores. Tilt-lock recommends using electric chain hoists with 115-1-60 power supply and a lifting speed of 16 fpm.
The Tilt Lock Model L3 Tip Lift is designed to handle rolls of paper up to 2,000 pound 826 s. The L3 utilizes two actuators to increase the output force to twice that of the L2 model Tip Lift. The L3 model utilizes handle mounted controls combining hoist and tip lift functions at the operators finger tips. The controls also integrate an interlock feature that requires
the operator to have both hands in the correct position on the controls preventing accidental hand placement. The Model L3 weighs 245 pounds. Electric actuator not to exceed 10 cycles per hour under full load. Actuator motor is thermally protected against excessive heat build up during operation. After cooling down actuator will resume normal operation. Tip Lift power
requirement is 115-1-60 and 15 amps. Minimum 3" wide roll is required for probes to work properly. Tip Lift is supplied with a quick release pin for interchanging probes to accommodate 3" to 12" diameter cores. Tilt-lock recommends using electric chain hoists with 115-1-60 power supply and a lifting speed of 16 fpm.
