|
|
|
|
|
The Multistat "Ex":
The Multistat "Ex" is a modern high-voltage power pack with fully electronic watchdog function. It is fitted with an automatic fault alarm, an analog display for operating voltage monitoring and an output jack for the connection of peripheral alarm units.
This power pack is installed outside explosive areas.
The Multistat "Ex" is designed according to VDE 0745, protection type I, IP 54 and has prototype test certificate BVS 95.Y.6003 X.
|
|
|
|
|
|
|
| |
Specifications Multistat "Ex":
| Nominal input voltage |
115 V ~ / 50 - 60 Hz
Order-No.: 01.7759.030
230 V ~ / 50 - 60 Hz
Order-No.: 01.7760.030 |
| Nominal output voltage |
ca. 7 - 8 kV ~ |
| Power consumption |
ca. 50 VA |
| Output short-circuit current |
<=3 mA |
Max. connected load
(ionizing unit incl. high voltage cable): |
15 m |
Special accessories:
Connector with driver |
|
|
|
|
The EI "Ex" ionizing bar:
The EI "Ex" ionizing bar is constructed to conform with the provisions of VDE 0171. It is suitable for use in operating areas at risk of explosions caused by combustible materials of explosion class 1 in the area of ignition group G1 - G4. Certifying authority "Physical-Technical Federal Institute" with test certificate
PTB no. III B/E-29 628.
|
|
|
|
|
|
|
| |
Specifications Ionizing unit EI "Ex":
| Diameter: |
25 mm |
| available from |
250 - 2.500 mm |
| High-voltage cable |
> 3 m |
For connection with the EN 92 "Ex" and Argonaut "Ex" power packs, the ionizing bar must be ordered with a special "Telemechanique" type X-3050 coupling.
Special accessories:
The ionizing bar can be supplemented with compressed air support from an air gate. This accessory is particularly suitable for blowing-off processes on plate and web material or where installation is difficult, e.g. in the case of longer distances from the material.
Two basic units of types LS "Ex" and KL "Ex" are available.
Air consumption figures can be given on request.
|
|
|
|
|
The "Ex" ring ionizer:
The "Ex" ring ionizer is supplied as a hand-held unit with compressed air gun, type 04.7191.000 or for fixed installation, type 04.7190.000. With compressed air support these units are ideally suited to the blowing-off of workpiece surfaces.
At the same time, electrostatic charges on non-conductive material can be eliminated in one process.
The units are constructed to conform with the provisions of VDE 0171 explosion protection and have prototype test certificate
BVS 95.Y.6003 X, classification Ex s IIA T4.
|
|
|
|
|
|
|
| |
Specifications: "Ex" ring ionizer
RI "Ex" hand-held unit with
compressed air gun |
Order-No.: 04.7191.000 |
| RI "Ex" for fixed installation |
Order-No.: 04.7190.000 |
| Diameter |
70 mm |
| air nozzle diameter |
2 mm |
| High-voltage cable |
> 3 m |
Air consumption depends on pressure and figures are available on request.
Special accessories:
| Standard bracket for 04.7190.001 |
Order-No.: 10.7206.000 |
Filter control valve with manometer,
including oil/water separator |
Order-No.: 11.7210.000 |
Air hose with fabric insert,
diameter 12 x 6 mm (outside/inside),
silicon-free |
Order-No.: X-6615 |
|
|
|
|
|
Power pack
The EN 92 "Ex" and Argonaut "Ex"
power packs are suitable for direct use in zone 1 explosive areas. All high-voltage components are accommodated in a flameproof Ex "d" housing. Both power packs have a high-voltage connection for the connection of an ionizing unit.
|
|
|
Long high-voltage cables are not required, since the power packs can be installed in the immediate vicinity of the ionizing unit. The EN 92 "Ex" power pack has no electronic watchdog function. The Argonaut "Ex" power pack is fitted with the "Argontronic" electronic watchdog timer. This requires an operator display with accessories.
Both power packs are designed to conform with VDE 0171
Part 1 ff. IEC 79/1, conformity certificate INIEX 82.103.183 and as equipment conform to the requirements for explosion protection under EN 50 014 ff./IEC 79/1 for d II BT 60. |
|
|
|
| |
Specifications EN 92 "Ex" und Argonaut "Ex":
| |
EN 92 "Ex"
|
Argonaut "Ex"
|
Nominal input voltage |
Order-No.: 04.7190.000 |
Order-No.: 04.7190.000 |
| 115 V ~/50 - 60 Hz |
01.7746.000 |
01.7751.000 |
| 230 V ~/50 - 60 Hz |
01.7747.000 |
01.7750.000 |
| high voltage cable |
> 3 m |
> 3 m |
|
|
|
|
| Nominal output voltage |
ca. 7 - 8 kV |
ca. 7 - 8 kV ~ |
| Power consumption |
ca. 50 VA |
ca. 50 VA |
| Output short-circuit current |
>=3 mA |
>=3 mA |
high voltage cable
(incl. ionizing unit ) |
15 m |
|
Special accessories with ARGONAUT "Ex":
Operator display, display panel, connection unit on request.
We reserve the right to technical modifications!
|
